Manual Height Adjustable Workstations
Features and Specifications:
- Cantilevered-style leg
- Seated to standing operator adjustability, from the fifth to the 95th percentile, (27" to 39" without work surface)
- Work surface configurations available: 24", 30" and 36" depths; 36", 48", 60", 72", and 96" lengths
- Strong open deck frame easily accepts tilting work surfaces, retractable ball transfers, recessed wells, etc.
- Designed to meet ANSI/HFS 100-1988
- Generous under table leg room helps with ADA compliance
- Frame accepts BOSTONtec casters
- Finished with a gray epoxy powder coat
Manual Height-Adjustable Cantilevered Design
This frame has been designed with sufficient strength and stability to support a variety of tasks in a broad range of environments. Height adjustments are made by removing the locking hand screw, repositioning the telescoping leg to the desired height and replacing the locking hand screw. This frame is best for single-shift, single-operator applications where frequent height changes are not required. A rear fixing frame provides stable support for uprights to hold bin rails, shelving, articulating modules, and lighting. A complete offering of drawers and storage cabinets is available.
This frame has been designed with sufficient strength and stability to support a variety of tasks in a broad range of environments. Height adjustments are made by removing the locking hand screw, repositioning the telescoping leg to the desired height and replacing the locking hand screw. This frame is best for single-shift, single-operator applications where frequent height changes are not required. A rear fixing frame provides stable support for uprights to hold bin rails, shelving, articulating modules, and lighting. A complete offering of drawers and storage cabinets is available.
| Ordering Information | ||
| Part No. | Manual Base Frame | Weight (lbs.) |
| AF2436 | 24" x 36" Work Surface | 97 |
| AF2448 | 24" x 48" Work Surface | 107 |
| AF2460 | 24" x 60" Work Surface | 118 |
| AF2472 | 24" x 72" Work Surface | 125 |
| AF3036 | 30" x 36" Work Surface | 99 |
| AF3048 | 30" x 48" Work Surface | 104 |
| AF3060 | 30" x 60" Work Surface | 120 |
| AF3072 | 30" x 72" Work Surface | 131 |
| AF3096 | 30" x 96" Work Surface | 142 |
| AF3648 | 36" x 48" Work Surface | 111 |
| AF3660 | 36" x 60" Work Surface | 122 |
| AF3672 | 36" x 72" Work Surface | 131 |
| AF3696 | 36" x 96" Work Surface | 142 |
| Note: Order work surface separately | ||
Features and Specifications:
- Center-justified style leg
- Seated to standing operator adjustability, from the fifth to the 95th percentile, (27" to 39" without work surface)
- Work surface configurations available: 30", 36" and 48" depths; 36", 48", 60", 72", and 96" lengths
- Strong open deck frame easily accepts retractable ball transfers, recessed wells, etc.
- Designed to meet ANSI/HFS 100-1988
- Generous under table leg room helps with ADA compliance
- Frame accepts BOSTONtec casters
- Finished with a gray epoxy powder coat
Manual Height Adjustable Center-Justified Design
This frame has been designed to support a wide range of tasks in a variety of environments. It is particularly useful for applications requiring access to the task from all sides. Adjustable from seated to standing height, 27" to 39". Height adjustments are made by removing the locking hand screw, repositioning the leg to the desired height, and securing the locking hand screw. This table is intended for single-shift, single-operator applications where frequent height changes are not required. This center-justified frame does not support uprights.
This frame has been designed to support a wide range of tasks in a variety of environments. It is particularly useful for applications requiring access to the task from all sides. Adjustable from seated to standing height, 27" to 39". Height adjustments are made by removing the locking hand screw, repositioning the leg to the desired height, and securing the locking hand screw. This table is intended for single-shift, single-operator applications where frequent height changes are not required. This center-justified frame does not support uprights.
| Ordering Information | ||
| Part No. | Manual CJ Base Frame | Weight (lbs.) |
| AFC3036 | 30" x 36" Work Surface | 94 |
| AFC3048 | 30" x 48" Work Surface | 99 |
| AFC3060 | 30" x 60" Work Surface | 115 |
| AFC3072 | 30" x 72" Work Surface | 126 |
| AFC3648 | 36" x 48" Work Surface | 106 |
| AFC3660 | 36" x 60" Work Surface | 117 |
| AFC3672 | 36" x 72" Work Surface | 126 |
| AFC3696 | 36" x 96" Work Surface | 137 |
| AFC4872 | 48" x 72" Work Surface | 116 |
| AFC4896 | 48" x 96" Work Surface | 124 |
| Note: Order work surface separately | ||
Trolley Frames
Features and Specifications:
- Accepts all standard BOSTONtec accessories
- Accessories adjust at one-inch increments
- Loading capacity: 300 lbs.
- Uprights: 14 gauge cold rolled steel
- Finished with a gray epoxy powder coat
- Order casters separately
- Weight: 50 lbs.
The BOSTONtec trolley frame has been designed using two uprights to provide as little obstruction as possible to shelf access. Trolleys accept all standard 30" BOSTONtec accessories and articulating arms.
| Ordering Information | |
| Part No. | Description |
| TTF3073 | Trolley, 30" X 73" |
| Note: Order work surface separately | |
Designed for Light Duty Applications
These frames provide a cost-effective means of supporting a small work surface and the convenient accessory modules available from BOSTONtec. The work surface height can be adjusted manually in one-inch increments when installed. This frame works best for single-shift, single-operator applications.
Without a work surface, the frames are often used behind conveyors to provide easy access and support for tools and task items.
Features and Specifications:
To learn more about BOSTONtec's height-adjustable, ergonomic and customizable workstations, let's talk.
These frames provide a cost-effective means of supporting a small work surface and the convenient accessory modules available from BOSTONtec. The work surface height can be adjusted manually in one-inch increments when installed. This frame works best for single-shift, single-operator applications.
Without a work surface, the frames are often used behind conveyors to provide easy access and support for tools and task items.
Features and Specifications:
- 150 pound work surface loading
- Accepts 24" x 30" or 24" x 36" work surface
- Work surface height adjustable in one-inch increments
- Single-bay frame width 30", height 72"
- Double-bay frame width 60", height 72"
- Uprights are slotted on both sides and accept accessories on both sides
- Uprights accept all BOSTONtec shelving, articulating modules and lightingv
- Available with end-justified or center-justified foot
- Finished with a gray epoxy powder coat
- Order work surface and surface support arms separately
- Frame accepts BOSTONtec caster sets
- Weight: see "Ordering Information", below, right
| Ordering Information | ||
| Part No. | Description | Weight (lbs.) |
| SWF3069 | Standing WS Frame, 30" | 53 |
| SWF6069 | Standing WS Frame, 60" | 73 |
| SWFA24 | Standing WS 19.5" Arm Set | 5 |
| SWFCB | Standing WS Frame Cross Bar | 3 |
| Note: Order work surface separately | ||
To learn more about BOSTONtec's height-adjustable, ergonomic and customizable workstations, let's talk.
Standing Workstation Frame
This frame has been designed to support a wide range of tasks in a variety of environments. It is particularly useful for applications requiring access to the task from all sides. Adjustable from seated to standing height, 27" to 39". Height adjustments are made by removing the locking hand screw, repositioning the leg to the desired height, and securing the locking hand screw. This table is intended for single-shift, single-operator applications where frequent height changes are not required. This center-justified frame does not support uprights.
This frame has been designed to support a wide range of tasks in a variety of environments. It is particularly useful for applications requiring access to the task from all sides. Adjustable from seated to standing height, 27" to 39". Height adjustments are made by removing the locking hand screw, repositioning the leg to the desired height, and securing the locking hand screw. This table is intended for single-shift, single-operator applications where frequent height changes are not required. This center-justified frame does not support uprights.
